(Default is 10PM for all days.) Days of the week will then flash on screen. Select desired off time and press Set ( ). My Off Time: Press “my off time” button and the clock will begin flashing.Use arrows ( ) to select the day(s) you want the timer to be active and press Set ( ). (Default is 6PM for all days.) Days of the week will then flash on screen. Use arrows to set the desired on time ( ) and press Set ( ). My On Time: Press “my on time” button and the clock will begin flashing.Use arrows ( ) to select the correct day options and press set ( ). Days of the week will flash on the screen. Use arrows ( ) to adjust time (time can be adjusted up to 1 hour in either direction) and press Set ( ). Evening – Sunset to 12:AM: Press “evening” button and the sunset time will flash on the screen.To deactivate program, press the button again and the LED will turn off. Note: If the LED on a button is illuminated, this indicates that the program is active. Once settings are complete, either wait 10 seconds and the timer will automatically go to clock mode, or press and hold “Set” ( ) for 3 seconds. Use the ( ) to scroll to the setting you were at. To re-enter settings, press and hold Set ( ) for 3 seconds. Note: If no button is pushed for 10 seconds, the timer will go back to clock mode. Use ( ) to select “ON” if you would like the timer to automatically adjust for Daylight Savings Time or “OFF” if you would not like the timer to adjust automatically. “DST” (Daylight Savings Time) will flash on the screen.Zone is used to determine sunrise/sunset times.
Use ( ) to select current zone (see Figure 1). Use ( ) to select the current day and press Set ( ). Use ( ) to select the current month and press Set ( ). Use ( ) to select the current year and press Set ( ). Use ( ) to select current time and press Set ( ). Hold Set ( ) for 3 seconds and current time will flash on the screen. Note: When timer is reset, the time will flash. Use up ( ) and down ( ) arrows to set current time. DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.).SHUT OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE INSTALLATION.Turn the power on at the circuit breaker or fuse box. Place rocker/decorator wallplate on timer, being careful to not overtighten wallplate screws.ġ4. Fasten the timer to the wall box using the screws provided.ġ3. Be sure the TOP (indicated on yoke of timer) is facing up. Insert timer into the 2 1/2" wall box, being careful not to pinch any wires. NOTE: Be sure that all wires and wire nuts are secure.ġ2. Tug each wire to verify connection, retighten if needed. Add the neutral wire to all neutral wires bound together and retighten the wire nut, making sure that the wire nut is tight.ġ1. There may be several neutral wires bound together. Often the neutral wire (white) can be found in the back of the wire box connected with a wire nut. Connect the neutral wire from the timer to the neutral wire in the box. Insert and tighten jumper wire into the hole marked NEUTRAL.ġ0. Remove white jumper wire from the package. Attach ground wire from box to the ground lug on the timer.ĩ. Insert the load side wire from the wire box into hole marked LOAD and tighten the LOAD screw.Ĩ. Insert the line side wire from the wire box into hole marked LINE and tighten the LINE screw.ħ. When loosening terminal screws, stop when you feel resistance.Ħ. Loosen the LINE and LOAD screws with either a flat-blade or Phillips screwdriver. Look at the back of the timer and you will see LINE, LOAD, NEUTRAL and GROUND.ĥ. Remove current wallplate and switch from wall box.ģ. Turn power off at circuit breaker or fuse box before installation.Ģ. If you are unsure about the installation of this timer please contact a licensed electrician.ġ. User Guide for Digital Timer Installation Instructions
#GE SMART TOUCH TIMER 25055 MANUAL MANUAL#
MyTouchSmart 26893 24-Hour in-Wall Digital Timer - Use Manual - Use Guide PDF.
0 kommentar(er)
